Wrote very basic brainfuck interpreter in 8086 asm to work on making it run and prove Turing completeness

.gitignore

@@ -5,4 +5,6 @@
 *.swp
 cpu/boot_code.bin
 cpu/boot_code.txt
+cpu/brainfuck.bin
+cpu/brainfuck.txt
 cpu/memdump.txt

README.md

@@ -4,7 +4,7 @@ A CPU that aims to be binary compatible with the 8086 and with as many optimisat
 
 ### Progress
 * [X] Executing code
-* [ ] can calculate the sieve of Eratosthenes
+* [ ] Is turing complete
 * [ ] can boot up MS-DOS / FreeDOS
 * [ ] Is completely binary compatible
 * [ ] Is pipelined

cpu/Makefile

@@ -2,34 +2,38 @@ SOURCES=processor.v testbench.v memory.v registers.v alu.v
 INCLUDES=proc_state_def.v
 VVP=processor.vvp
 
+.PHONY: brainf
+brainf: ${VVP} brainfuck.txt
+	vvp ${VVP} +BOOT_CODE=brainfuck.txt
+
 .PHONY: run
-run: ${VVP}
+run: ${VVP} boot_code.txt
 	vvp ${VVP}
 
 .PHONY: build
 build: ${VVP}
 
 .PHONY: wave
-wave: ${VVP}
-	vvp ${VVP} -lxt2
+wave: ${VVP} brainfuck.txt
+	vvp ${VVP} -lxt2  +BOOT_CODE=brainfuck.txt
 	gtkwave test.lx2 gtkwave_savefile.gtkw
 
-${VVP} : ${SOURCES} ${INCLUDES} boot_code.txt
+${VVP} : ${SOURCES} ${INCLUDES}
 	iverilog -g2012 ${SOURCES} -o $@
 
-.PHONY: clean
-clean:
-	rm -f ${VVP} test.lx2 boot_code.txt boot_code.bin
+%.txt:%.bin
+	dd if=/dev/zero bs=1 count=1200 of=$(subst .bin,.stage,$^) status=none
+	dd if=$^ of=$(subst .bin,.stage,$^) conv=notrunc,nocreat status=none
+	xxd -ps -c 2 $(subst .bin,.stage,$^) > $@
+	rm $(subst .bin,.stage,$^)
 
-boot_code.txt:boot_code.bin
-	dd if=/dev/zero bs=1 count=256 of=boot_code.stage status=none
-	dd if=boot_code.bin of=boot_code.stage conv=notrunc,nocreat status=none
-	xxd -ps -c 2 boot_code.stage > boot_code.txt
-	rm boot_code.stage
-
-boot_code.bin:boot_code.asm
+%.bin:%.asm
 	as86 -0 $< -b $@
 
 .PHONY: disas
-disas: boot_code.bin
-	objdump -D -b binary -m i8086 boot_code.bin
+disas: brainfuck.bin
+	objdump -D -b binary -m i8086 $^
+
+.PHONY: clean
+clean:
+	rm -f ${VVP} test.lx2 boot_code.txt boot_code.bin brainfuck.txt brainfuck.bin

cpu/brainfuck.asm

@@ -0,0 +1,105 @@
+mov si,#prog
+mov BX,#data
+mov CX,#bracket
+dec si
+INTERPRET:
+inc si
+mov al,[si]
+cmp al,#'+
+jz WAS_PLUS
+cmp al,#'-
+jz WAS_MINUS
+cmp al,#'>
+jz WAS_MR
+cmp al,#'<
+jz WAS_ML
+cmp al,#'[
+jz WAS_PL
+cmp al,#']
+jz WAS_PR
+cmp al,#'.
+jz WAS_PRINT
+jmp PROG_END
+
+WAS_PLUS:
+inc BYTE [BX]
+JMP INTERPRET
+
+WAS_MINUS:
+dec BYTE [BX]
+JMP INTERPRET
+
+WAS_MR:
+inc bx
+JMP INTERPRET
+
+WAS_ML:
+dec bx
+JMP INTERPRET
+
+WAS_PL:
+MOV AL,[BX]
+cmp AL,#0
+jz SKIP_CODE_BLOCK
+;have to enter loop
+MOV AX,SI
+inc CX
+inc CX
+push SI
+MOV SI,CX
+mov [SI],AX
+POP SI
+JMP INTERPRET
+
+SKIP_CODE_BLOCK:
+;have to skip loop
+MOV DX,#0
+SKIP_LOOP:
+INC SI
+mov AL,[SI]
+CMP AL,#']
+JZ WAS_CLOSE1
+CMP AL,#'[
+JZ WAS_OPEN1
+JMP SKIP_LOOP
+
+WAS_CLOSE1:
+CMP DX,#0
+JZ INTERPRET
+DEC DX
+JMP SKIP_LOOP
+WAS_OPEN1:
+INC DX
+JMP SKIP_LOOP
+
+WAS_PR:
+mov AL,[BX]
+cmp AL,#0
+JZ EXIT_PR
+push SI
+MOV SI,CX
+mov ax,[SI]
+POP SI
+mov si,ax
+JMP INTERPRET
+
+
+EXIT_PR:
+DEC CX
+DEC CX
+jmp INTERPRET
+
+
+WAS_PRINT:
+mov ah, #0x02
+MOV DL,[BX]
+int #0x21
+JMP INTERPRET
+
+PROG_END:
+hlt
+
+bracket: .BLKB 280
+data: .BLKB 560
+;prog db '++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++.f'
+prog:.ASCII '++++++++[>++++[>++>+++>+++>+<<<<-]>+>+>->>+[<]<-]>>.>---.+++++++..+++.>>.<-.<.+++.------.--------.>>+.>++.'

cpu/memory.v

@@ -1,7 +1,10 @@
 module rom(input [19:0] address,output wire [15:0] data ,input rd,input cs);
-reg [15:0] memory [0:127];
+reg [15:0] memory [0:599];
 initial begin
-	$readmemh("boot_code.txt", memory);
+	string boot_code;
+	if(!$value$plusargs("BOOT_CODE=%s",boot_code))
+		boot_code="boot_code.txt";
+	$readmemh(boot_code, memory);
 end
 assign data = !rd & !cs ? memory[address]: 'hz;
 endmodule

cpu/processor.v

@@ -11,7 +11,7 @@ assign out = (sel == 'b00) ? in1 :
 	in4;
 endmodule
 
-module processor ( input clock, input reset , output reg [19:0] external_address_bus, inout [15:0] external_data_bus,output reg read, output reg write, output reg HALT);
+module processor ( input clock, input reset, output reg [19:0] external_address_bus, inout [15:0] external_data_bus,output reg read, output reg write, output reg HALT,output reg ERROR);
 
 /*** Global Definitions ***/
 // State
@@ -35,7 +35,6 @@ always @(negedge reset) begin
 		@(posedge clock);
 		state=`PROC_HALT_STATE;
 		ProgCount=0;//TODO: Reset Vector
-		EXCEPTION=0;
 		HALT=0;
 		reg_read=1;
 		reg_write=1;
@@ -48,8 +47,6 @@ always @(negedge reset) begin
 	end
 end
 
-reg EXCEPTION;
-
 /*** ALU and EXEC stage logic ***/
 
 //Architectural Register file
@@ -91,7 +88,7 @@ ADDER16 ADDER16_1(ADDER16_1A,ADDER16_1B,ALU_OUT,ADDER16_1O,ADDER16_1C);
 
 /*** Processor stages ***/
 
-`define invalid_instruction state=`PROC_IF_STATE_ENTRY;EXCEPTION=1;
+`define invalid_instruction state=`PROC_IF_STATE_ENTRY;ERROR=1;
 
 always @(negedge clock) begin
 	case(state)
@@ -132,7 +129,7 @@ always @(posedge clock) begin
 		`PROC_HALT_STATE:begin
 		end
 		`PROC_IF_STATE_ENTRY:begin
-			EXCEPTION=0;
+			ERROR=0;
 			external_address_bus <= ProgCount;
 			read <= 0;
 			write <= 1;
@@ -268,7 +265,7 @@ always @(posedge clock) begin
 		`PROC_EX_STATE_ENTRY:begin
 			reg_data=ADDER16_1O;
 			state=`PROC_EX_STATE_EXIT;
-			EXCEPTION=0;
+			ERROR=0;
 		end
 	endcase
 end

cpu/testbench.v

@@ -7,8 +7,9 @@ reg  clk_enable;
 wire [19:0]address_bus;
 wire [15:0]data_bus;
 wire rd,wr,romcs,HALT;
+wire ERROR;
 
-processor p(clock,reset,address_bus,data_bus,rd,wr,HALT);
+processor p(clock,reset,address_bus,data_bus,rd,wr,HALT,ERROR);
 rom bootrom(address_bus,data_bus,rd,romcs);
 
 `define CPU_SPEED 1000
@@ -36,6 +37,13 @@ always @(posedge HALT) begin
 	$finish;
 end
 
+always @(posedge ERROR) begin
+	$display("PROCESSOR RUN INTO AN ERROR.\nCycles run for: %d",cycles);
+	$writememh("memdump.txt", bootrom.memory);
+	#(`CPU_SPEED) //Just for the waveform
+	$finish;
+end
+
 always @(posedge clock)begin
 	if(reset==1)
 		cycles=cycles+1;