Fixed warning about standards compliance

cpu/memory.v

@@ -1,5 +1,5 @@
 module rom(input [19:0] address,output wire [15:0] data ,input rd,input cs);
-reg [15:0] memory [15:0];
+reg [15:0] memory [0:15];
 initial begin
 	$readmemh("boot_code.txt", memory);
 end

cpu/processor.v

@@ -1,58 +1,5 @@
-`timescale 1ns/1ps
 `include "proc_state_def.v"
 
-module clock_gen (input enable, output reg clk);
-
-parameter FREQ = 1000;  // in HZ
-parameter PHASE = 0;    // in degrees
-parameter DUTY = 50;    // in percentage 
-
-real clk_pd	= 1.0/FREQ * 1000000; 	// convert to ms
-real clk_on	= DUTY/100.0 * clk_pd;
-real clk_off	= (100.0 - DUTY)/100.0 * clk_pd;
-real quarter	= clk_pd/4;
-real start_dly	= quarter * PHASE/90;
-
-reg start_clk;
-
-initial begin
-end
-
-// Initialize variables to zero
-initial begin
-	clk <= 0;
-	start_clk <= 0;
-end
-
-// When clock is enabled, delay driving the clock to one in order
-// to achieve the phase effect. start_dly is configured to the 
-// correct delay for the configured phase. When enable is 0,
-// allow enough time to complete the current clock period
-always @ (posedge enable or negedge enable) begin
-	if (enable) begin
-		#(start_dly) start_clk = 1;
-	end else begin
-		#(start_dly) start_clk = 0;
-	end      
-end
-
-// Achieve duty cycle by a skewed clock on/off time and let this
-// run as long as the clocks are turned on.
-always @(posedge start_clk) begin
-	if (start_clk) begin
-		clk = 1;
-
-		while (start_clk) begin
-			#(clk_on)  clk = 0;
-			#(clk_off) clk = 1;
-		end
-
-		clk = 0;
-	end
-end 
-endmodule
-
-
 module processor ( input clock, input reset , output reg [19:0] external_address_bus, inout [15:0] external_data_bus,output reg read, output reg write, output reg HALT);
 /* State */
 reg [3:0] state;

cpu/testbench.v

@@ -1,3 +1,5 @@
+`timescale 1ns/1ps
+
 module tb;
 wire clock;
 reg reset;
@@ -29,3 +31,56 @@ initial begin
 	#50 $finish;
 end
 endmodule
+
+
+/*Clock generator*/
+module clock_gen (input enable, output reg clk);
+
+parameter FREQ = 1000;  // in HZ
+parameter PHASE = 0;    // in degrees
+parameter DUTY = 50;    // in percentage 
+
+real clk_pd	= 1.0/FREQ * 1000000; 	// convert to ms
+real clk_on	= DUTY/100.0 * clk_pd;
+real clk_off	= (100.0 - DUTY)/100.0 * clk_pd;
+real quarter	= clk_pd/4;
+real start_dly	= quarter * PHASE/90;
+
+reg start_clk;
+
+initial begin
+end
+
+// Initialize variables to zero
+initial begin
+	clk <= 0;
+	start_clk <= 0;
+end
+
+// When clock is enabled, delay driving the clock to one in order
+// to achieve the phase effect. start_dly is configured to the 
+// correct delay for the configured phase. When enable is 0,
+// allow enough time to complete the current clock period
+always @ (posedge enable or negedge enable) begin
+	if (enable) begin
+		#(start_dly) start_clk = 1;
+	end else begin
+		#(start_dly) start_clk = 0;
+	end      
+end
+
+// Achieve duty cycle by a skewed clock on/off time and let this
+// run as long as the clocks are turned on.
+always @(posedge start_clk) begin
+	if (start_clk) begin
+		clk = 1;
+
+		while (start_clk) begin
+			#(clk_on)  clk = 0;
+			#(clk_off) clk = 1;
+		end
+
+		clk = 0;
+	end
+end 
+endmodule